Kodama Forum

Search found 52 matches

Go to advanced search

by edefault
Tue Sep 19, 2017 8:38 am
Forum: Slicer Discussion & Support
Topic: Print Pauses After S3D 4.0 Update
Replies: 2
Views: 373

Re: Print Pauses After S3D 4.0 Update

I had a ticket open with Kodama Support recently on some "cold extrusion prevented" error message during every first layer of print with S3D 4.0 on Ubuntu. There is a parallel thread here about "clicking noise" where I mentioned this ... with the help of Kodama Roi I managed to g...
by edefault
Fri Sep 08, 2017 9:34 am
Forum: Proven Solutions
Topic: No Filament extruding and/or "clicking noise"
Replies: 56
Views: 11278

Re: No Filament extruding and/or "clicking noise"

Is there a way to update the firmware from S3D or something on Ubuntu?
by edefault
Thu Sep 07, 2017 4:00 pm
Forum: Proven Solutions
Topic: No Filament extruding and/or "clicking noise"
Replies: 56
Views: 11278

Re: No Filament extruding and/or "clicking noise"

Thanks a lot ... I'll give that a try when my current print job is finished (just another 7 hours of 21:30).
About technial explanations: I love it, so you're welcome with these anytime.
by edefault
Thu Sep 07, 2017 2:18 pm
Forum: Proven Solutions
Topic: No Filament extruding and/or "clicking noise"
Replies: 56
Views: 11278

Re: No Filament extruding and/or "clicking noise"

1) Firmware version.
2) PCB version.
3) Fan type (new or old).
4) Simplify3d version.


Firmware: Panowin Paladin 3.6.2-D3
PCB: 6.1 (it replaced a 4.1 Version)
Fan has a dot
Simlify3D: Ubgraded to 4.0 recently

Why the fan plays a role here is beyond me ... since it's purely analogue.
by edefault
Thu Sep 07, 2017 11:45 am
Forum: Proven Solutions
Topic: No Filament extruding and/or "clicking noise"
Replies: 56
Views: 11278

Re: No Filament extruding and/or "clicking noise"

Your problem may be solved by a firmware re-flashing
... thus deliver recognizable temperature values to Simplify3D?
by edefault
Tue Sep 05, 2017 6:37 pm
Forum: Hardware Tips & Mods
Topic: Another Nasty SD Card Print Interruption: USB & Reboot
Replies: 2
Views: 263

Re: Another Nasty SD Card Print Interruption: USB & Reboot

No, definitely ... the very moment the computer rebooted Trinus interrupted printing. I don't want to reproduce this since there's already a plethora of reasons why printing doesn't finish properly, from tangled filament to clogged nozzles. Yes, I'd like to print directly from the computer via USB c...
by edefault
Tue Sep 05, 2017 6:51 am
Forum: Hardware Tips & Mods
Topic: Another Nasty SD Card Print Interruption: USB & Reboot
Replies: 2
Views: 263

Another Nasty SD Card Print Interruption: USB & Reboot

Just in case ... while printing from SD card one should make sure to remove the USB cable, esp. when it is still hooked up to some computer. I had to restart mine and didn't think much about the USB connection to the busy Trinus - and poop! My print was interrupted half way done. And no way to resum...
by edefault
Tue Sep 05, 2017 6:43 am
Forum: Hardware Support
Topic: [ERROR] cold extrusion prevented
Replies: 2
Views: 720

Re: [ERROR] cold extrusion prevented

"cold extrusion prevented" is what I always get from S3D 4.0 on Ubuntu a few minutes into the first layer (of a part that quite fills the bed size of my Trinus). And guess what? Exporting the very same part from Pango on Windows to SD card file, then printing from that one via LCD display ...
by edefault
Thu Aug 31, 2017 2:21 pm
Forum: Deutsch
Topic: Extrudermotor wird nicht mehr angesteuert
Replies: 12
Views: 1108

Re: Extrudermotor wird nicht mehr angesteuert

Fortsetzung: Neuer Versuch mit dem stärkeren Netzteil (Kodama Shop NL) und einem LCD Display (dto.; darauf hatte ich bisher verzichtet). Ganz orthodox mit dem WIndows Computer eines Bekannten Pango installiert, Teil platziert und "pcode" auf SD Karte geschrieben. Spannend! Der Druckstart v...
by edefault
Tue Aug 29, 2017 3:04 pm
Forum: Hardware Support
Topic: Filament Bed Adhesion
Replies: 4
Views: 407

Re: Filament Bed Adhesion

The first layer is the most important, and fine tuning the z offset makes the difference: if it is too big the first layer won't stick, if it is too small it will be hard work to remove it. The S3D "leveling assistant" is pretty helpful - put a sheet of paper on the print bed, then start t...